No heat, won't tumble, or taking two cycles to dry a load — a licensed technician comes to your door and gives you a flat, written price before any work starts. Most dryers are fixed in one visit.
Fast. Honest. Local to Naperville.
Your technician arrives with common parts already on the truck — heating elements, belts, and igniters — so most dryer repairs in Naperville don't need a second trip.
A tripped breaker, faulty gas valve, or a failed heating element are the most common causes.
Usually a motor issue, a broken drive belt, or worn drum rollers keeping the drum from turning.
Usually lint buildup, a blocked duct, or a pinched vent pipe restricting airflow out of the dryer.
Igniter, gas valve, and safety-critical repairs handled by technicians trained for gas appliances.
A clogged vent is a fire risk and the top cause of "takes forever to dry" — we clean it while we're already there.
Laundromats and multi-unit buildings in Naperville — high-cycle machines, faster turnaround.
No stock-photo promises — this is what a dryer repair visit actually looks like, from diagnosis to the finished fix.
Most Naperville dryer calls are one visit — parts stay stocked on the truck.
Tell us gas or electric, the brand, and what it's doing. We'll give you a same-day or next-day window.
We check the heating element or igniter, the belt and motor, the moisture sensor, and the vent for blockages.
You see the full parts-and-labor price in writing before we touch anything.
We run a real drying cycle to confirm heat and airflow are back to normal, backed by a 90-day warranty.
Runs and tumbles fine but clothes stay wet — check for a tripped breaker, a faulty gas valve, or a failed heating element.
Motor malfunction, a broken belt, or worn drum rollers are the usual causes.
Almost always an airflow restriction — lint buildup, a blocked duct, or a pinched vent pipe.
Often a faulty moisture sensor ending the cycle before clothes are actually dry.
Usually worn drum rollers, a glide bearing, or an idler pulley that needs replacing.
A safety-relevant symptom — often tied to lint buildup or a vent blockage restricting airflow. Worth addressing right away.
A clogged dryer vent is one of the most common causes of "runs but doesn't dry" — and a real fire hazard if it's never been cleaned. We can inspect and clean it in the same visit as your repair.
Every job gets its own written quote after diagnosis — these are typical ranges to help you plan, not a fixed price for your unit.
| Repair | Typical range | Common driver |
|---|---|---|
| Service call / diagnostic visit | $70 – $130 | Applied toward the repair if you approve the work |
| Non-spinning dryer repair | $30 – $250 | Worn belt, motor issue, or drum rollers |
| Heating element replacement | $150 – $250 | Runs and tumbles, but clothes stay wet |
| Not heating (general) | $80 – $420 | Tripped breaker, gas valve, or heating element |
| Gas dryer repairs | +$50 – $100 vs. electric | Igniter and gas-valve parts, added safety work |
| Overall typical range | $100 – $430 (avg $180) | Combined parts-and-labor estimate |
Ranges reflect typical parts-and-labor costs across the industry. Your exact price depends on the brand, model, and the part that failed — confirmed in writing before we start.
We'd rather tell you to replace an old machine than sell you a repair that won't last. A quick rule of thumb:
Most repairs run between $30 for a minor fix and $450 for a bigger tumble/motor issue, with heating element replacements typically $150-$250 and a typical overall range of $100-$430. You'll get a flat, written quote for your specific dryer after diagnosis — before any repair starts.
Yes, in most cases. Call in the morning and we can usually get a Naperville technician out that same day, subject to schedule.
That's a "no heat" symptom, most often caused by a tripped breaker, a faulty gas valve, or a failed heating element. It's usually diagnosed and fixed in one visit.
Yes — gas and electric. Gas dryer repairs (igniters, gas valves) typically run about $50-$100 more than electric due to the added safety and specialized parts involved.
Yes. A clogged vent is one of the top causes of a dryer that takes forever to dry a load — and a fire risk if it's never been cleaned. We can inspect and clean it during the same visit as your repair.
If the repair cost is under half the price of a comparable new unit and the dryer is under about 10 years old, repair usually makes sense. If the motor or control board has failed or the unit is over 13 years old, replacement is often the better value — we'll give you an honest read during the visit.
All major brands including Whirlpool, Samsung, LG, GE, Maytag, Kenmore, Bosch, and Speed Queen.
Call now for a same-day appointment window, or book online and we'll confirm within the hour.
Naperville